BKKWJ - UNISORB V-100 EPOXY GROUT JOINT FILLER

  • MSDS: BKKWJ
  • Manufacturer: AKEMI PLASTICS INC
  • Product Name: UNISORB V-100 EPOXY GROUT JOINT FILLER
  • National Stock Number: 8030-00N014241
Product Identification

Product ID:UNISORB V-100 EPOXY GROUT JOINT FILLER
MSDS Date:03/01/1990
FSC:8030
NIIN:00N014241
MSDS Number: BKKWJ

Responsible Party
AKEMI PLASTICS INC
5265 S CLINTON TRAIL
EATON RAPIDS, MI 48827
US

Emergency Phone: 517-663-8191

Info Phone: 517-764-6060

Cage: AKEMI

Contractor
AKEMI PLASTICS INC
EATON RAPIDS, MI 48827 US

Telephone: 517-764-6060

Cage: AKEMI

Ingredients

EPON 820 (EPOXY RESIN)

CAS: 25068-38-6

RTECS: KC2100000

Fraction By Weight: 55-60%


TITANIUM DIOXIDE

CAS: 13463-67-7

RTECS: XR2275000

Fraction By Weight: 1-5%

OSHA PEL 15 MG/M3 TDUST

ACGIH TLV: 10 MG/M3 TDUST; 9293


GLYCOLS, POLYPROPYLENE, 2,3-EPOXYPROPYL ETHER (EPOXY RESIN)

CAS: 9072-62-2

RTECS: MD0913000

Fraction By Weight: 20-30%


KAOLIN

CAS: 1332-58-7

RTECS: GF1670500

Fraction By Weight: 1-5%

OSHA PEL 15 MG/M3 TDUST

ACGIH TLV: 2 MG/M3 TDUST; 9293


SILICA, CRYSTALLINE - QUARTZ

CAS: 14808-60-7

RTECS: VV7330000

Fraction By Weight: 10-15%

OSHA PEL SEE TABLE Z3

ACGIH TLV: 0.1 MG/M3 RDUST;9293


SILICA GEL (FUMED SILICA)

CAS: 112945-52-5

RTECS: VV7310000

Fraction By Weight: 0-1%

OSHA PEL 6 MG/M3

ACGIH TLV: 10 MG/M3 TDUST


AIR RELEASE ADDITIVE

Fraction By Weight: 0-1%

OSHA PEL 50 PPM (MFR)

ACGIH TLV: 25 PPM (MFR)


GLYCERIN

CAS: 56-81-5

RTECS: MA8050000

Fraction By Weight: 0-1%

OSHA PEL 15 MG/M3 TDUST

ACGIH TLV: 10 MG/M3 (MIST) 9293

Hazards

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:NO Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:YES OSHA:NO
Health Hazards Acute and Chronic:EYE:MINOR TRANSIENT IRRITATION, NO
CORNEAL INJURY LIKELY. SKIN:MINOR IRRITATION, MAY BE SKIN
SENSITIZER. NOT LIKELY TO BE ABSORBED THROUGH SKIN IN TOXIC
AMOUNTS. INGEST:LOW ACUTE ORAL TOXICITY. INHAL: NO GUIDE FOR
CONTROL KNOWN. NOT CONSIDERED PROBLEM UNLESS HEATED TO HIGH
TEMPERATURE.
Explanation of Carcinogenicity:SILICA CRYSTALLINE-QUARTZ:IARC-GROUP 2A.
Effects of Overexposure:SKIN:REDNESS, DERMATITIS. EYE:REDNESS,
IRRITATION.
Medical Cond Aggravated by Exposure:SKIN:CONTACT DERMATITIS.

First Aid

First Aid:EYE:FLUSH W/WATER FOR AT LEAST 15 MINUTES. CALL MD. SKIN:WASH
W/SOAP & WATER. INGEST:CALL MD IMMEDIATELY. INHAL:REMOVE TO FRESH
AIR. SUPPORT BREATHING (GIVE O*2/ARTIFICIAL RESPIRATION), CALL MD
IMMEDI ATELY .

Fire Fighting

Flash Point:>200F,>93C
Extinguishing Media:WATER SPRAY, FOAM, CARBON DIOXIDE OR DRY CHEMICAL.
Fire Fighting Procedures:USE NIOSH/MSHA APPROVED SCBA AND FULL
PROTECTIVE EQUIPMENT.
Unusual Fire/Explosion Hazard:DECOMPOSITION AND COMBUSTION PRODUCTS MAY
BE TOXIC.

Accidental Release

Spill Release Procedures:SOAK UP W/ABSORBENT MATERIAL OR SCRAPE UP.
RESIDUAL CAN BE REMOVED WITH NON-FLAMMABLE SOLVENT.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling

Handling and Storage Precautions:AVOID PROLONGED OR REPEATED INHALATION
OF VAPORS AND SKIN CONTACT. STORE IN DRY AREA AWAY FROM HEAT. DO
NOT EAT, DRINK OR SMOKE WHILE USING PRODUCT.
Other Precautions:FOLLOW ALL PRECAUTIONS CONTAINED ON MSDS WHEN
PERFORMING MAINTENANCE OR NON-ROUTINE OPERATIONS ON EQUIPMENT OR
CONTAINERS WHICH CONTAIN OR HAVE CONTAINED THIS MATERIAL.

Exposure Controls

Respiratory Protection:NOT NEEDED WHEN USED UNDER RECOMMENDED
CONDITIONS. IF NEEDED, USE NIOSH/MSHA APPROVED RESPIRATOR
APPROPRIATE FOR EXPOSURE OF CONCERN .
Ventilation:LOCAL AND MECHANICAL EXHAUST RECOMMENDED.
Protective Gloves:PLASTIC OR RUBBER GLOVES.
Eye Protection:CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:LONG SLEEVED AND LONG LEGGED CLOTHING.
Work Hygienic Practices:WASH HANDS THOROUGHLY AFTER USE AND BEFORE
EATING, DRINKING, SMOKING OR USING SANITARY FACILITIES .
Supplemental Safety and Health
NONE SPECIFIED BY MANUFACTURER.

Chemical Properties

HCC:V7
Spec Gravity:1.26
Solubility in Water:NEGLIGIBLE
Appearance and Odor:THIXOTROPIC WHITE PASTE, MILD ODOR.

Stability

Stability Indicator/Materials to Avoid:YES
STRONG AMINES AND ACIDS.
Stability Condition to Avoid:NONE SPECIFIED BY MANUFACTURER.
Hazardous Decomposition Products:CO, CO*2, ALDEHYDES AND ACIDS.

Disposal

Waste Disposal Methods:DISPOSE OF I/A/W LOCAL, STATE AND FEDERAL
REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.